| |
| ULTRA PARALLEL BLOCKS
(Sizes are nominal) |
 |
Used for accurate supporting
of jobs
Made from special quality alloy steel material.
Hardness 60 ± 2 Rc.
Accuracy for Parallelism, Squareness & flatness
is 0.005mm upto 200mm L & 0.010mm upto 450mm L
Special sizes can also be manufactured. |
|
| |
|
| ULTRA SUPPORT SCREW JACK |
|
|
Used for supporting the job.
Made from good quality alloy steel material.
Safe & reliable adjustment of height.
Locknut for adjustment.
Can be used with different pads. |
| Sr
No. |
Cat
No. |
Size
(mm) |
Range
(mm) |
| 1. |
UL
- 30401 |
Ø
40 |
50 - 70 |
| 2. |
UL
- 30402 |
Ø
50 |
100 - 150 |
| 3. |
UL
- 30403 |
Ø
60 |
150 - 250 |
| 4. |
UL
- 30404 A |
Pad
Ø 25 |
----- |
| 5. |
UL
- 30404 B |
Pad
Ø 25 |
----- |
| 6. |
UL
- 30404 C |
Pad
Ø 25 |
----- |
| 7. |
UL
- 30404 D |
Pad
Ø 25 |
----- |
| 8. |
UL
- 30404 E |
Pad
Ø 25 |
----- |
| 9. |
UL
- 30404 F |
Pad
Ø 60 |
----- |
| 10. |
UL
- 30405 SET |
(1+1)Pair
jack - Ø 40 & Ø 50 + Pad A to F-1no. each |
----- |
| 11. |
UL
- 30406 SET |
(1+1)Pair
jack - Ø 50 & Ø 60 + Pad A to F-1no. each |
----- |
|
| ULTRA MAGNETIC VICE |
 |
Used for holding flat squared
& round jobs.
Accuracy for Flatness, Squareness & parallelism
within 0.005mm.
"V" on moveable jaw facilitates end face grinding.
Job is clamped only by resting between fixed
& moveable jaw and operating On-Off switch.
ON-OFF facility by allen key. |
| Sr.No. |
Cat
No. |
Size
(mm) |
Jaw
Holding Area (mm2) |
| 1. |
UL-20401 |
110
x 180 x 75 |
100
x 65 |
| 2. |
UL-20402 |
160
x 225 x 90 |
150
x 75 |
|
| ULTRA HARDENED AND
GROUND PRECISION GRINDING VICE |
|
Used for holding the jobs,
spark erosion operation, right angle grinding & Light
machining.
Made from high quality alloy steel.
Accuracy for Square ness, Flatness & Parallelism within
0.005mm.
Jaw pressure on work piece is forward & downward for repeatable
positioning & maximum holding power.
All sides can be used as reference.
Hardness - 60 ± 2 Rc & Tempered.
“V” on moveable jaw for better gripping of round jobs.
Also available in stainless steel |
| Sr.No. |
Cat.No |
Size
(mm) |
Jaw
Opening (mm) |
| 1. |
UL
-31001 |
150L
x 48W x 60H |
0
- 75 |
| 2. |
UL
-31002 |
180L
x 63W x 70H |
0
- 90 |
| 3. |
UL
-31003 |
200L
x 73W x80H |
0
- 100 |
| 4. |
UL
-31004 |
235L
x 96W x 96H |
0
- 130 |
|
| ULTRA HARDENED AND
GROUND PRECISION GRINDING VICE Screw Type |
 |
Used for holding the jobs,
right angle grinding & Light machining.
Made from high quality alloy steel.
Accuracy for Squareness, Flatness & Parallelism within
0.005mm.
Hardness 60 ± 2 Rc & Tempered.
Wear Plate at bottom to prevent lifting of Jaw
Hardened clamping screw with square thread & gun metal nut
Tenon at bottom to allow easy alignment with machine bed
|
Also available in stainless steel
| Sr.No. |
Cat.No |
Size
(mm) |
Jaw
Height (mm) |
Opening
(mm) |
Step
in Jaw (mm) |
| 1. |
UL
- 31101 |
150L
x 45W x 45 H |
22 |
0
- 70 |
3x2 |
| 2. |
UL
- 31102 |
175L
x 60W x 44 H |
28 |
0
- 80 |
3x3 |
| 3. |
UL
- 31103 |
190L
x 75W x 65 H |
32 |
0
- 85 |
4x3 |
| 4. |
UL
- 31104 |
210L
x 95W x 75 H |
38 |
0
- 95 |
5x3 |
|
| ULTRA SINE VICE |
|
Used for Precision
measurement, setting of angles,
Right angle grinding & light machining.
Made from high quality alloy steel.
Accuracy for Squareness, Flatness & Parallelism
within ± 0.005mm.
Angular accuracy within ± 5 seconds.
Centre distance between rollers is within ±0.005mm
Hardness - 60 ± 2 Rc & Tempered |
| Sr.No. |
Cat
No. |
Size
(mm) |
C.D
(mm) |
Opening
(mm) |
| 1. |
UL-31201 |
190L x 65W x 85H |
100 |
80 |
| 2. |
UL-31202 |
235L
x 76W x 100H |
150 |
110 |
| 3. |
UL-31203 |
265L
x 95W x 105H |
150 |
125 |
| 4. |
UL-31204 |
290L
x 120W x 120H |
200 |
145 |
| 5. |
UL-31205 |
310L
x 140W x145H |
200 |
150 |
|
| ULTRA
SINE BAR |
|
Used for Precision
measurement, setting of angles.
Made from high quality alloy steel.
Accuracy for Squareness, Flatness & Parallelism is
within 0.005mm.
Centre distance between rollers is within ±0.005mm
Hardness - 60 ± 2 Rc & Tempered |
| Sr.No. |
Cat.No. |
Size
(mm) |
C.D
(in mm) |
| 1. |
UL
- 31301 |
130L
x 25 W x 60H |
100 |
| 2. |
UL
- 31302 |
245L
x 40W x 60H |
200 |
| 3. |
UL
- 31303 |
350L
x 55W x 80H |
300 |
Magnetic Sine Bar is also available
|
| ULTRA SINE-TABLE IS :
5939-1970 |
|
Used for Precision
measurement, setting of angles
utilizing slip gauge & light machining.
Accuracy for squareness, Parallelism & flatness is
0.005mm upto 200L & 0.010mm upto 450L.
Angle can be set within ±5 seconds.
Centre Distance between rollers is within 0.005mm.
Made from high quality alloy steel
Hardness - 60 ± 2 Rc & Tempered.
Firm hinged clamp to reduce possibility of distortion.
M6 & M8 tapped holes for job clamping.
|
| SR.No. |
Cat
No. |
Size
(mm) |
Center
Distance |
Inclination |
| 1. |
UL
- 40101 |
150
L x 120 W x 65 H |
70 |
0 - 45º |
| 2. |
UL
- 40102 |
250
L x 150 W x 65 H |
100 |
0 - 45º |
| 3 |
UL
- 40103 |
300
L x 150 W x 65 H |
100 |
0 - 45º |
| 4. |
UL
- 40104 |
450
L x 150 W x 65 H |
100 |
0 - 45º |
|
| ULTRA COMPOUND
SINE-TABLE IS : 5939 - 1970 |
 |
Used for Precision
measurement, setting of angles & Light machining.
Accuracy for Square ness, Flatness & Parallelism
within 0.005mm upto 200L & 0.010mm upto 450L.
Angle can be set within ±5 seconds.
Centre Distance between rollers is within 0.005mm.
Made from high quality alloy steel.
Compound Angle facility.
Hardness - 60 ± 2 Rc & Tempered.
Firm hinged clamp to reduce possibility of distortion.
M6 & M8 tapped holes for job clamping. |
| Sr.No. |
Cat
No. |
Size
(mm) |
Bottom
C.D |
Top
C.D |
| 1. |
UL-
40201 |
150
L x 100 W x 95 H |
100
mm |
50
mm |
| 2. |
UL-
40202 |
250
L x 150 W x 95 H |
150
mm |
100
mm |
| 3. |
UL-
40203 |
300
L x 150 W x 95 H |
200
mm |
100
mm |
| 4. |
UL-
40204 |
450
L x 150 W x 105 H |
300
mm |
100
mm |
|
| ULTRA MAGNETIC
SINE-TABLE IS : 5939- 1970 |
 |
Used for Precision
measurement, setting of angles & Light machining.
Accuracy for Square ness, Flatness & Parallelism
within 0.005mm upto 200L & 0.010mm upto 450L.
Angle can be set within ±5 seconds.
Centre Distance between roller is within 0.005mm.
Made from high quality alloy steel
Hardness - 60 ± 2 Rc & Tempered.
Magnetic Table for job holding.
Firm hinged clamp to reduce possibility of distortion. |
| Sr.No |
Cat.No |
Size
(mm) |
Center
Distance |
Inclination |
| 1. |
UL-
40301 |
150
L x 120 W x 105 H |
70
mm |
0 - 45º |
| 2. |
UL-
40302 |
250
L x 150 W x 105 H |
100
mm |
0 - 45º |
| 3. |
UL-
40303 |
300
L x 150 W x 105 H |
100
mm |
0 - 45º |
| 4. |
UL-
40304 |
450
L x 150 W x 105 H |
100
mm |
0 - 45º |
| 5. |
UL-
40305 |
500
L x 200 W x 105 H |
150
mm |
0 - 45º |
|
|
BACK / NEXT
|
|
