| “ULTRA”
ELECTROMAGNETIC RECTANGULAR CHUCK IS : 8710 - 1978 |
|
Work holding device for
surface grinding machines.
Magnetic flux is generated by one or two coils.
Accuracy as per IS : 8710 - 1978.
Magnetic pull is as per IS specification.
Mag - D - Mag with variable control unit allows to
neutralize the residual magnetism precisely , using a
microprocessor based control circuitry.
Variable supply to vary power which helps in alignment & removing of
warpages of thin jobs.
Chuck is tested for Slippering force, Waterproof test,
Temperature rise test, Electrical & Demagnetizing tests.
We also manufacture Special chucks to suit individual
requirements.
Good quality & standard electrical accessories.
|
Work holding device for
surface grinding machines.
Each pole is having separate coil, as such very strong
& even magnetic flux is generated.
Accuracy as per IS : 8710 - 1978.
Magnetic pull is 30-50% more then IS specification.
Mag - D - Mag with variable control unit allows to
neutralize the residual magnetism precisely , using a microprocessor
based control circuitry.
Variable supply to vary power which helps in alignment
& removing of warpages of thin jobs.
Chuck is tested for Slippering force, Waterproof test, Temperature rise
test, Electrical & Demagnetizing tests.
Also available in Longitudinal Poles.
We also manufacture Special chucks to suit individual
requirements.
Good quality & standard electrical accessories. |
| Sr.
No. |
Size
(mm) |
Pole
Gap (mm) |
Pole
Pitch |
Cat
No. |
Cat
No. |
| 1. |
450
L x 150 W x 100 H |
15 |
40 |
UL-71301 |
UL-71401 |
| 2. |
500
Lx 200 W x 100 H |
15 |
40 |
UL-71302 |
UL-71402 |
| 3. |
600 Lx
200 W x 100 H |
15 |
40 |
UL-71303 |
UL-71403 |
| 4. |
600 Lx
250 W x 100 H |
15 |
40 |
UL-71304 |
UL-71404 |
| 5. |
750
Lx 250 W x 100 H |
15 |
40 |
UL-71305 |
UL-71405 |
| 6. |
900 Lx
250 W x 100 H |
15 |
40 |
UL-71306 |
UL-71406 |
| 7. |
600 Lx
300 W x 100 H |
15 |
40 |
UL-71307 |
UL-71407 |
| 8. |
750 Lx
300 W x 100 H |
15 |
40 |
UL-71308 |
UL-71408 |
| 9. |
900 Lx
300 W x 100 H |
15 |
40 |
UL-71309 |
UL-71409 |
| 10. |
1000 Lx
250 W x 110 H |
15 |
40 |
UL-71310 |
UL-71410 |
| 11. |
1000 Lx
300 W x 110 H |
15 |
40 |
UL-71311 |
UL-71411 |
| 12. |
1500 Lx
250 W x 110 H |
15 |
40 |
UL-71312 |
UL-71412 |
| 13. |
1500 Lx
300 W x 110 H |
15 |
40 |
UL-71313 |
UL-71413 |
| 14. |
1500 Lx
400 W x 110 H |
15 |
40 |
UL-71314 |
UL-71414 |
| 15A. |
"ULTRA"
MAG d- MAG WITH VARIABLE |
|
Upto
1000L 2 Amp. |
|
|
| |
CONTROL
UNIT |
|
Upto
1500L 3 Amp. |
|
|
| 15B. |
"ULTRA"
MAG d- MAG WITH VARIABLE |
|
Upto
1000L 2 Amp. |
|
|
| |
CONTROL
UNIT & BATTERY BACK UP (20MIN) |
|
Upto
1500L 3 Amp. |
|
|
|
“ULTRA”
HEAVY DUTY FINE PITCH MULTI COIL ELECTRO
MAGNETIC CHUCK ( Transverse Pole ) IS - 8710 - 1978 |
 |
Work holding device for
surface grinding machines.
Each pole is having separate coil, as such very strong & even
magnetic flux is generated.
Accuracy as per IS : 8710 - 1978.
Magnetic pull is 30-50% more then IS specification.
Fine Pitch (4 + 1) makes it suitable to hold thin & small
jobs.
Mag - D - Mag with variable control unit allows to neutralize the
residual magnetism precisely , using a microprocessor based control
circuitry.
Variable supply to vary power which helps in alignment & removing of
warpages of thin jobs.
Chuck is tested for Slippering force, Waterproof test, Temperature
rise test, Electrical & Demagnetizing tests.
Also available in Longitudinal Poles. |
| Sr.
No. |
Cat
No. |
Size
(mm) |
Pole
Gap (mm) |
| 1. |
UL-71501 |
450
L x 150 W x 100 H |
4
+ 1 |
| 2. |
UL-71502 |
500
Lx 200 W x 100 H |
4
+ 1 |
| 3. |
UL-71503 |
600 Lx
200 W x 100 H |
4
+ 1 |
| 4. |
UL-71504 |
600 Lx
250 W x 100 H |
4
+ 1 |
| 5. |
UL-71505 |
750
Lx 250 W x 100 H |
4
+ 1 |
| 6. |
UL-71506 |
900 Lx
250 W x 100 H |
4
+ 1 |
| 7. |
UL-71507 |
600 Lx
300 W x 100 H |
4
+ 1 |
| 8. |
UL-71508 |
750 Lx
300 W x 100 H |
4
+ 1 |
| 9. |
UL-71509 |
900 Lx
300 W x 100 H |
4
+ 1 |
| 10. |
UL-71510 |
1000 Lx
250 W x 110 H |
4
+ 1 |
| 11. |
UL-71511 |
1000 Lx
300 W x 110 H |
4
+ 1 |
| 12. |
UL-71512 |
1500 Lx
250 W x 110 H |
4
+ 1 |
| 13. |
UL-71513 |
1500 Lx
300 W x 110 H |
4
+ 1 |
| 14. |
UL-71514 |
1500 Lx
400 W x 110 H |
4
+ 1 |
| 15A. |
"ULTRA"
MAG d- MAG WITH VARIABLE CONTROL UNIT |
Upto
1000L 2 Amp. |
| |
|
Upto
1500L 3 Amp. |
| 15B. |
"ULTRA"
MAG d- MAG WITH VARIABLE CONTROL UNIT & BATTERY BACK UP
(20MIN) |
Upto
1000L 2 Amp. |
| |
|
Upto
1500L 3 Amp. |
|
| “ULTRA”
MULTI COIL MICRO FINE PITCH ELECTRO MAGNETIC CHUCK |
 |
Work holding device for
surface grinding machines.
Each pole is having separate coil, as such very strong & even
magnetic flux is generated.
Accuracy as per IS : 8710 - 1978.
Magnetic pull is 30-50% more then IS specification.
Fine Pitch (1 + 0.5) makes it suitable to hold very thin & small
jobs.
Mag - D - Mag with variable control unit allows to neutralize the
residual magnetism precisely , using a microprocessor based control
circuitry.
Variable supply to vary power which helps in alignment & removing of
warpages of thin jobs.
Chuck is tested for Slippering force, Waterproof test, Temperature rise
test, Electrical & Demagnetizing tests.
Good quality & standard electrical accessories.
We also manufacture Special chucks to suit individual requirement.
|
| Sr.
No. |
Cat
No. |
Size
(mm) |
Pole
Gap (mm) |
| 1. |
UL-72201 |
450
L x 150 W x 100 H |
1.5 |
| 2. |
UL-72202 |
450
Lx 200 W x 100 H |
1.5 |
| 3. |
UL-72203 |
500
Lx 200 W x 100 H |
1.5 |
| 4. |
UL-72204 |
600 Lx
250 W x 100 H |
1.5 |
| 5. |
UL-72205 |
750
Lx 250 W x 100 H |
1.5 |
| 15A. |
"ULTRA"
MAG D- MAG WITH VARIABLE CONTROL UNIT |
2
Amp. |
| 15B. |
"ULTRA"
MAG d- MAG WITH VARIABLE CONTROL UNIT & BATTERY BACK UP
(20MIN) |
2
Amp. |
|
| “ULTRA”
ELECTRO MAGNETIC ROUND CHUCK IS : 8710 - 1978 |
 |
Work holding device for Rotary
surface grinding machine & lathe machines.
Each pole is having separate coil, as such very strong & even
magnetic flux is generated.
Magnetic pull is 30-50% more then IS specification.
Mag - D - Mag with variable control unit allows to neutralize the
residual magnetism precisely , using a microprocessor based control
circuitry.
Variable supply for varying power which helps in alignment &
removing of warpages of thin jobs.
The chuck is also useful for second operation
Chuck is tested for Slippering force, Waterproof test, Temperature rise
test, Electrical & Demagnetizing tests.
|
| Sr.
No. |
Cat
No. |
Size
(mm) |
Pole
Gap (mm) |
| 1. |
UL-71601 |
Ø300
X 100H |
10
+ 4 |
| 2. |
UL-71602 |
Ø450
X 100H |
10
+ 4 |
| 3. |
UL-71603 |
Ø600
X 100H |
10
+ 4 |
| 4. |
UL-71604 |
Ø750
X 100H |
10
+ 4 |
| 5. |
UL-71605 |
Ø1000
X 100H |
10
+ 4 |
| 15A. |
"ULTRA"
MAG D- MAG WITH VARIABLE CONTROL UNIT |
2
Amp. |
| 15B. |
"ULTRA"
MAG d- MAG WITH VARIABLE CONTROL UNIT & BATTERY BACK UP
(20MIN) |
2
Amp. |
|
“ULTRA”
FINE PITCH ELECTROPERM MAGNETIC CHUCK
For Grinding Machine |
 |
Work holding device for
surface grinding machines.
COLD DEVICE as it doesn't require power continuously except for short
period of activation & deactivation.
Parallelism & flatness is 0.010mm/300mm.
Suitable for thin & small jobs.
Economical for operation & maintenance.
Uniform clamping force all over surface.
Negligible power consumption.
No accidents due to power failure.
Slippering force is 2.5 Kg/cm².
Vertical Lifting Force is 35 - 40 Kg/cm².
Variable supply unit to vary power which helps in alignment &
removing of warpages of thin jobs.
Chuck is tested for Slippering force, Waterproof test, Temperature rise
test, Electrical & Demagnetizing tests.
Good quality & standard electrical accessories.
We also manufacture Special chucks to suit individual requirement. |
| Sr.
No. |
Cat
No. |
Size
(mm) |
Pole
Gap (mm) |
| 1. |
UL
71701 |
450
L x150 W x 100 H |
25 |
| 2. |
UL-71702 |
500
Lx 200 W x 100 H |
25 |
| 3. |
UL-71703 |
600
Lx 200 W x 100 H |
25 |
| 4. |
UL-71704 |
600
Lx 250 W x 100 H |
25 |
| 5. |
UL-71705 |
750
Lx 250 W x 100 H |
25 |
| 6. |
UL
71706 |
900
Lx 250 W x 100 H |
25 |
| 7. |
UL
71707 |
600
Lx 300 W x 100 H |
25 |
| 8. |
UL
71708 |
750
Lx 300 W x 100 H |
25 |
| 9. |
UL
71709 |
900
Lx 300 W x 100 H |
25 |
| 10. |
UL
71710 |
1000
Lx 250 W x 100 H |
25 |
| 11. |
UL
71711 |
1000
Lx 300 W x 100 H |
25 |
| 12. |
UL
71712 |
1500
Lx 250 W x 100 H |
25 |
| 13. |
UL
71713 |
1500
Lx 300 W x 100 H |
25 |
| 14. |
UL
71714 |
1500
Lx 400 W x 100 H |
25 |
| 15. |
“ULTRA”
CONTROL UNIT WITH VARIABLE SUPPLY |
25 |
|
| “ULTRA”
FINE PITCH ELECTROPERM MAGNETIC CHUCK For Grinding Machine |
 |
Work holding device for
surface grinding machines.
COLD DEVICE as it doesn't require power continuously except for short
period of activation & deactivation.
Parallelism & flatness is 0.010mm/300mm.
Suitable for thin & small jobs.
Economical for operation & maintenance.
Uniform clamping force all over surface.
Negligible power consumption.
No accidents due to power failure.
Slippering force is 2.5 Kg/cm².
Vertical Lifting Force is 35 - 40 Kg/cm².
Variable supply unit to vary power which helps in alignment &
removing of warpages of thin jobs.
Chuck is tested for Slippering force, Waterproof test, Temperature rise
test, Electrical & Demagnetizing tests.
Good quality & standard electrical accessories.
We also manufacture Special chucks to suit individual requirement. |
| Sr.
No. |
Cat
No. |
Size
(mm) |
Pole
Gap (mm) |
| 1. |
UL
72301 |
450
L x150 W x 100 H |
4
+ 1 |
| 2. |
UL-72302 |
500
Lx 200 W x 100 H |
4
+ 1 |
| 3. |
UL-72303 |
600
Lx 200 W x 100 H |
4
+ 1 |
| 4. |
UL-72304 |
600
Lx 250 W x 100 H |
4
+ 1 |
| 5. |
UL-72305 |
750
Lx 250 W x 100 H |
4
+ 1 |
| 6. |
UL
72306 |
900
Lx 250 W x 100 H |
4
+ 1 |
| 7. |
UL
72307 |
600
Lx 300 W x 100 H |
4
+ 1 |
| 8. |
UL
72308 |
750
Lx 300 W x 100 H |
4
+ 1 |
| 9. |
UL
72309 |
900
Lx 300 W x 100 H |
4
+ 1 |
| 10. |
UL
72310 |
1000
Lx 250 W x 110 H |
4
+ 1 |
| 11. |
UL
72311 |
1000
Lx 300 W x 110 H |
4
+ 1 |
| 12. |
UL
72312 |
1500
Lx 250 W x 110 H |
4
+ 1 |
| 13. |
UL
72313 |
1500
Lx 300 W x 110 H |
4
+ 1 |
| 14. |
UL
72314 |
1500
Lx 400 W x 110 H |
4
+ 1 |
| 15. |
“ULTRA”
CONTROL UNIT WITH VARIABLE SUPPLY |
4
+ 1 |
|
| “ULTRA”
PERMANENT MAGNETIC LIFTER |
 |
Used for lifting &
handling of steel plates, heavy block & castings as well as heavy
round or cylindrical parts.
The 1 : 3 safety factor of the recommended load to the Test load ensures
use at optimal working conditions even with Substantial air gaps &
surface conditions.
Compact design, strong magnetic pull, total work safety
Easy operated lever for ON-OFF.
Spring loaded block at side for safety feature.
Suitable for Flat & Round jobs.
No damage on job during operation.
|
| Sr.
No. |
Cat
No. |
Size
(mm) |
Lifting
Capacity |
Tested
Capacity |
Weight |
| 0 |
UL
80500 |
85 L X 60 W X 75H |
100 Kg |
300 Kg |
2.5 Kg |
| 1. |
UL
80501 |
170
L x 85 W x 105 H |
200
Kg |
600
Kg |
9
Kg |
| 2. |
UL-
80502 |
170
Lx 85 W x 105 H |
250
Kg |
750
Kg |
9
Kg |
| 3. |
UL-
80503 |
230
Lx 85 W x 105 H |
300
Kg |
900
Kg |
14
Kg |
| 4. |
UL-
80504 |
230
Lx 85 W x 105 H |
450
Kg |
1350
Kg |
14
Kg |
| 5. |
UL-
80505 |
290
Lx 90 W x 125 H |
600
Kg |
1800
Kg |
28
Kg |
| 6. |
UL
80506 |
300
Lx 150 W x 125 H |
700
Kg |
2100
Kg |
30
Kg |
| 7. |
UL
80507 |
365
Lx 150 W x 170 H |
1000
Kg |
3000
Kg |
80
Kg |
| 8. |
UL
80508 |
480
Lx 210 W x 185 H |
1500
Kg |
4500
Kg |
125
Kg |
| 9. |
UL
80509 |
485
Lx 230 W x 240 H |
2000
Kg |
6000
Kg |
165
Kg |
|
| “ULTRA”
ELECTROPERM LIGHT DUTY CHUCK (47 x 47 Quard Pole) |
 |
Work holding device for
Milling machines.
COLD DEVICE as it doesn't require power continuously except for short
period of activation & deactivation.
Suitable for light milling i.e. 1-3 mm depth of cut at recommended speed
& feed.
Maximum material removal is possible.
Economical for operation & maintenance.
No accidents due to power failure.
Slippering force is 2.5 - 3 Kg/cm².
Vertical Lifting Force is 35 - 40 Kg/cm².
Variable supply unit to vary power which helps in alignment of
jobs.
Chuck is tested for Slippering force, Waterproof test, Temperature rise
test, Electrical & Demagnetizing tests.
Good quality & standard electrical accessories.
We also manufacture Special chucks to suit individual requirement. |
| Sr.
No. |
Cat
No. |
Size
(mm) |
| 1. |
UL
71801 |
600
L x300 W x 110 H |
| 2. |
UL-71802 |
750
Lx 300 W x 110 H |
| 3. |
UL-
71803 |
1000
Lx 300 W x110 H |
| 4. |
UL-
71804 |
1500
Lx 300 W x 110 H |
| 5. |
UL-
71805 |
600
Lx 400 W x 110 H |
| 6. |
UL-
71806
|
750
Lx 400 W x 110 H |
| 7. |
UL
-71807 |
1000
Lx 400 W x 110 H |
| 8. |
UL-71808 |
1500
Lx 400 W x 110 H |
| 9. |
ULTRA
CONTROL UNIT WITH VARIABLE SUPPLY |
|
“ULTRA”
ELECTROPERM HEAVY DUTY CHUCK
(70 x 70) Quard Pole |
 |
Work holding device for
conventional & CNC milling m/c.
COLD DEVICE as it doesn't require power continuously except for short
period of activation & deactivation.
Suitable for light milling i.e. 3-6 mm depth of cut at recommended speed
& feed.
Maximum material removal is possible.
Economical for operation & maintenance.
No accidents due to power failure.
Slippering force is 2.5 - 3.5 Kg/cm².
Vertical Lifting Force is 40 - 45 Kg/cm².
Variable supply unit to vary power which helps in alignment of
jobs.
Chuck is tested for Slippering force, Waterproof test, Temperature rise
test, Electrical & Demagnetizing tests.
Good quality & standard electrical accessories.
We also manufacture Special chucks to suit individual requirement
|
| Sr.
No. |
Cat
No. |
Size
(mm) |
| 1. |
UL
71901 |
600
L x300 W x 110 H |
| 2. |
UL-71902 |
750
Lx 300 W x 110 H |
| 3. |
UL-
71903 |
1000
Lx 300 W x110 H |
| 4. |
UL-
71904 |
1500
Lx 300 W x 110 H |
| 5. |
UL-
71905 |
600
Lx 400 W x 110 H |
| 6. |
UL-
71906 |
750
Lx 400 W x 110 H |
| 7. |
UL
-71907 |
1000
Lx 400 W x 110 H |
| 8. |
UL-71908 |
1500
Lx 400 W x 110 H |
| 9. |
ULTRA
CONTROL UNIT WITH VARIABLE SUPPLY |
|
“ULTRA”
ELECTRO MAGNETIC CHUCK For Cylindrical
Grinding |
 |
Work holding device on
Cylindrical Grinding m/c to grind outer diameter & face component as
bearing recess, flanges, collet bushes, discs etc.
Can also be used on Lathe machine.
Mag - D - Mag with variable control unit allows to neutralize the
residual magnetism precisely
Magnetic Coil (outer body) remains stationary & middle part (Round
body) will rotate with spindle through adaptor sleeve.
Variable supply is useful to true the job.
4 T-slots for easy location of job.
Chuck is tested for Slippering force, Temperature rise, Waterproof,
Electrical & Demagnetizing tests.
Good quality & standard electrical accessories.
Battery Back-up unit is also available on request |
| Sr.
No. |
Cat
No. |
Size
(mm) |
| 1. |
UL
72001 |
Ø100
[4"] |
|
|
Ø150
[6"] |
|
|
Ø200
[8" ] |
| 2. |
"ULTRA"
Mag- D-MAG Mag with Variable Control Unit |
|
| “ULTRA”
DEMAGNETISERS Series UL- 801 |
 |
Used for removing surface
residual magnetism.
Operate on 220V single phase AC supply.
Suitable for all types of steel such as HSS, Nickel chrome, spring
steel, die steel etc.
Foot switch for easy & safely operation.
Fibre top allows scratch free demagnetization.
|
| Sr.
No. |
Cat
No. |
Size
(mm) |
| 1. |
UL
80101 |
150
x1 00 |
| 2. |
UL
80102 |
150
x 150 |
| 3. |
UL
80103 |
150
x 225 |
| 4. |
UL
80104 |
150 x 300 |
| 5. |
UL 80105 |
350 x 350 |
|
| “ULTRA”
COIL TYPE DEMAGNETISERS |
 |
Used for removing surface
residual magnetism of round & cylindrical jobs.
Operate on 220V single phase AC supply.
Suitable for all types of steel such as HSS, Nickel chrome, spring
steel, die steel etc.
Foot switch for easy & safely operation.
Fibre body allows scratch free demagnetization. |
| Sr.
No. |
Cat
No. |
Size
(mm) |
| 1. |
UL
80201 |
Ø100
bore |
| 2. |
UL
80202 |
Ø150
bore |
| 3. |
UL
80203 |
Ø200
bore |
| 4. |
UL
80204 |
Ø300 bore |
| 5. |
UL 80205 |
050 x 100 x 100 |
| 6. |
UL 80206 |
050 x 200 x 200 |
| 7. |
UL 80207 |
100 x 200 x 200 |
|
